Eemax EMT6 – EMT6 Mini Tank Water Heater V, 6 Gallon – FEATURES EMT6 must be hardwired Point-of-use heating eliminates long hot water pipe runs. Electric Mini Tank Water Heaters EMT1 – EMT – EMT4 – EMT6 Installation and Operating Instruction Manual Table of Contents Important Safety Instructions. Get Eemax EMT6 Instructions / Assembly. Get all Eemax manuals!.

Author: Tygorr Nagami
Country: Botswana
Language: English (Spanish)
Genre: Spiritual
Published (Last): 3 April 2015
Pages: 193
PDF File Size: 3.23 Mb
ePub File Size: 5.33 Mb
ISBN: 280-3-14771-852-2
Downloads: 97807
Price: Free* [*Free Regsitration Required]
Uploader: Toshicage

When using electrical appliances, safety precautions to reduce the risk of fire, electric shock or injury to persons should be followed, including: This water heater must be grounded.

Eemax EMT6 Electric Mini Tank Water Heater – 6.0 gallon 120V, Hardwired

Connect only to properly grounded outlet. Install or locate this water heater only in accordance with the provided installation instructions.

Water Pressure psi Weight empty lbs. EMT models are designed to supply hot water for all hand wash and kitchen sinks in a residential, commercial or industrial environment. EMT models can replace traditional central hot water heaters thereby conserving water and reducing energy waste.

EMT models can also be plumbed in series with the central water heater and act as a booster.

The pressure vessel water tank is welded, glass lined steel and is equipped with an anode rod. The water heater is equipped with a thermostat and a high limit temperature switch. If Water pipes are copper or bronze, use dielectric connections to prevent corrosion. Failure to provide dielectric insulation may result in premature tank or nipple failure and may void your warranty.

Model: EMT6

Insure that the water heater is installed in a level position. Must NOT be smaller in diameter than the outlet diameter of the emt, or have any reducing couplings.


Must NOT be plugged or blocked. Must be made of suitable material for hot water. Must not have more than two elbows. Must terminate at an adequate drain. Must not have a shut off valve between relief valve and tank or relief valve and termination of discharge. Before connecting the power, fill the tank and system with water and check for leaks. To eemad sure that all air is out of the efmax system, open the hot water faucets on your fixtures until constant water flows from them.

Otherwise any air remaining in the tank will cause the water heater element to et6 destruct. If air remains in the tank, the element will be damaged when the electric cord is plugged in. Adhere to all pertinent State and local codes. You are now ready to use your water heater.

Tankless Water Heater Solutions for You | Eemax

Run the hot water at a nearby sink and evaluate the hot water temperature. Make any temperature adjustment using the section below: The water heater is equipped with an adjustable thermostat that once set will automatically control water temperature. The red indicator lamp remains illuminated while the water is being heated.

Call a service person plumber or electrician for service assistance. Always unplug the power supply cord when the water is turned off or when emr6 or draining the water heater. Before calling for service, first confirm that the water eemaax is properly filled and that VAC power has not been interrupted.

Scale deposits can affect the heating capability of the element. Heavy scale can even cause the element to burn out.

EemaX EMT6 Instruction manual |

The element can be descaled chemically or manually. Remove the heating element see above. To descale chemically, soak the heating element in white vinegar or other descaling solution and then rinse well with fresh water.


For various reasons the high limit safety shut off switch will occasionally dmt6 the eemac heater down. This shut down will occur when water temperatures exceed F. Power is automatically turned off to the heating element. Emh6 shut off device may activate as a result of eenax power outage or an electrical storm. Do not attempt to reset the high limit switch without first allowing the water heater to cool down the high temperature water inside the heater.

Water does not get hot 1. Make sure the power supply is on and working. If light does not come on, check that the reset button is pushed in; follow steps from previous section. If the indicator light is illuminated, but water temperature does not get hot at the sink, test for a plumbing crossover as follows; shut off cold water supply to water heater and open hot water tap.

There should be no water flowing. Name of Part Qty. Exclusions of Coverage from this Limited Warranty 1.

Manufacturer is not liable for any water damage or other damages arising, directly or indirectly, from any defect in the Eemax Mini Tank Water Heater component part s or from its use.

Manufacturer is not liable under this limited warranty or otherwise if: The water heater or any of its component parts have been subject to misuse, alteration, neglect or accident; or b. Electric Mini T ank W ater Heaters.

Page 20 Eemax Inc. Don’t see a manual you are looking for? Tell us what’s missing. Tell us about it. Or point us to the URL where the manual is located. Your manual failed to upload